Différences
Ci-dessous, les différences entre deux révisions de la page.
Les deux révisions précédentesRévision précédenteProchaine révision | Révision précédenteProchaine révisionLes deux révisions suivantes | ||
logiciel:internet:tmate:start [2022/05/15 14:26] – [Introduction] admin | logiciel:internet:tmate:start [2022/05/16 16:30] – [Utilisation] admin | ||
---|---|---|---|
Ligne 15: | Ligne 15: | ||
<WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
- | Savoir si on est en 32 ou 64 bits :<cli prompt=' | + | Savoir si on est en 32 ou 64 bits :<cli prompt=' |
- | x86_64</ | + | x86_64 |
- | Sur un Raspberry pi : | + | </ |
- | | + | Sur un Raspberry pi :<cli prompt=' |
- | : -> 32 bits | + | armv7l</ |
- | | + | <WRAP list-deep> |
- | : -> 64 bits | + | |
+ | | ||
</ | </ | ||
- | + | </ | |
- | - Repérez | + | <WRAP list-deep> |
- | | + | - Allez sur la page [[https:// |
- | | + | |
- | | + | - Descendez la page et repérez le lien qui vous correspond : |
- | | + | |
- | - Sur le PC à contrôler, selon votre cas, lancez ((copiez-collez le lien repéré sur la page ci-dessus)): | + | |
- | | + | |
+ | - Sur le PC à contrôler, selon votre cas, lancez (lien repéré sur la page ci-dessus) : | ||
+ | | ||
...@...:~$ tar xJf tmate-*amd64.tar.xz</ | ...@...:~$ tar xJf tmate-*amd64.tar.xz</ | ||
- | | + | |
...@...:~$ tar xJf tmate-*i386.tar.xz</ | ...@...:~$ tar xJf tmate-*i386.tar.xz</ | ||
- | | + | |
- | ...@...:~$ tar -xJf tmate-*arm32v7.tar.xz | + | pi@framboise4:~ $ tar -xJf tmate-2.4.0-static-linux-arm32v7.tar.xz</ |
- | </ | + | </WRAP> |
===== Configuration ===== | ===== Configuration ===== | ||
Ligne 43: | Ligne 45: | ||
===== Utilisation ===== | ===== Utilisation ===== | ||
- | - Placez-vous dans le répertoire créé par la décompression et lancez tmate :<cli prompt=' | + | - Placez-vous dans le répertoire créé par la décompression et lancez tmate :<cli prompt=' |
+ | To see the following messages again, run in a tmate session: tmate show-messages | ||
+ | Press <q> or < | ||
+ | --------------------------------------------------------------------- | ||
+ | Connecting to ssh.tmate.io... | ||
+ | Note: clear your terminal before sharing readonly access | ||
+ | web session read only: https:// | ||
+ | ssh session read only: ssh ro-RB7vLFgC2C4mPZg9PdJ6WLpdz@lon1.tmate.io | ||
+ | web session: https:// | ||
+ | ssh session: ssh sBWNthY6Epjbexd9z4s4Q7ppt@lon1.tmate.io | ||
+ | Error reading from channel: Socket error: Operation timed out | ||
+ | Reconnecting... (Error reading from channel: Socket error: Operation timed out) | ||
+ | Reconnected | ||
+ | </ | ||
+ | |||
+ | |||
+ | - <cli prompt=' | ||
...@...:~$ ./tmate | ...@...:~$ ./tmate | ||
Tip: if you wish to use tmate only for remote access, run: tmate -F [0/0] | Tip: if you wish to use tmate only for remote access, run: tmate -F [0/0] | ||
Ligne 101: | Ligne 119: | ||
* **(en)** [[http://]] | * **(en)** [[http://]] | ||
- | * **(fr)** [[http://]] | + | * **(fr)** [[https://www.metal3d.org/ |
---- | ---- | ||
- | //Basé sur << [[http://|Article]] >> par Auteur.// | + | //Basé sur << [[https:// |